Indoors, the GPS of a phone is often several metres off. The GPS Calibration page measures that gap on known spots of the plan; r-io suite then corrects every position the phone sends.
No capture of the tile interface yet: the captures of the r-io4U overview predate the redesign of November 2026 and show the former menus.
01
Reference points
A reference point is a precisely known spot of a 2D plan, marked by a printed QR code. The points are not part of the model: they are kept, per plan, in the reference points property of the project. In the web applications, the map menu of a 2D plan has a Reference points section that generates them and gives the PDF of their QR codes to print.
02
Measuring
The person stands on a reference point, scans its QR code (or taps I’m here) and keeps still about 15 seconds while the phone averages its positions; then again on two or three points spread out. Where there is no reference point, the person can touch the plan where she sees she is (Measure here): such a point counts half as much as a reference point. The page shows the gap of each point, the correction (north, east, height) and its precision; Save the calibration keeps it.
03
The correction applied by r-io suite
The calibration is kept on the GPS sensor of the phone, in its GPS calibration property. Every position the phone sends is corrected by the server before r-io suite uses it; the position measured by the phone is kept on the event, so that r-iose can show the raw and the corrected traces. Without calibration, r-io suite uses the positions as the phone measures them.
04
GPS test
The GPS test switch starts a test: while it is on, r-io suite receives only the positions the person sends with one button (Send the GPS position), after keeping still: the map shows where the GPS measured it and where r-io suite places the person once the calibration applied, to compare with where she really is. Where the phone has a barometer, the test tells whether it places the phone on the level of the plan; I’m on this level takes the height of the level shown as the reference of the barometer. Clear the positions sent empties the test.
05
What it needs
The person of the user must carry a phone with a GPS sensor in the use case, and the page needs the location of the device, so HTTPS in a browser (see In a browser). Scanning a QR code uses the camera.
En intérieur, le GPS d’un téléphone se trompe souvent de plusieurs mètres. La page GPS Calibration mesure cet écart sur des points connus du plan ; r-io suite corrige ensuite chaque position que le téléphone envoie.
Pas encore de capture de l’interface à tuiles : les captures de la vue d’ensemble de r-io4U précèdent la refonte de novembre 2026 et montrent les anciens menus.
01
Points de référence
Un point de référence est un endroit connu avec précision d’un plan 2D, marqué par un QR code imprimé. Les points ne font pas partie du modèle : ils sont gardés, par plan, dans la propriété reference points du projet. Dans les applications web, le menu de la carte d’un plan 2D a une rubrique Reference points qui les génère et donne le PDF de leurs QR codes à imprimer.
02
Mesurer
La personne se place sur un point de référence, scanne son QR code (ou touche I’m here) et reste immobile environ 15 secondes pendant que le téléphone moyenne ses positions ; puis de même sur deux ou trois points éloignés. Là où il n’y a pas de point de référence, la personne peut toucher le plan là où elle voit qu’elle est (Measure here) : un tel point compte moitié moins qu’un point de référence. La page montre l’écart de chaque point, la correction (nord, est, hauteur) et sa précision ; Save the calibration la garde.
03
La correction appliquée par r-io suite
La calibration est gardée sur le capteur GPS du téléphone, dans sa propriété GPS calibration. Chaque position envoyée par le téléphone est corrigée par le serveur avant que r-io suite ne l’utilise ; la position mesurée par le téléphone est gardée sur l’événement, si bien que r-iose peut montrer la trace brute et la trace corrigée. Sans calibration, r-io suite utilise les positions telles que le téléphone les mesure.
04
Test GPS
L’interrupteur GPS test lance un test : tant qu’il est actif, r-io suite ne reçoit que les positions que la personne envoie d’un seul bouton (Send the GPS position), après être restée immobile : la carte montre où le GPS l’a mesurée et où r-io suite place la personne une fois la calibration appliquée, à comparer avec l’endroit où elle est vraiment. Quand le téléphone a un baromètre, le test dit s’il place le téléphone au niveau du plan ; I’m on this level prend la hauteur du niveau affiché comme référence du baromètre. Clear the positions sent vide le test.
05
Ce qu’il faut
La personne de l’utilisateur doit porter un téléphone avec un capteur GPS dans le cas d’usage, et la page a besoin de la position de l’appareil, donc du HTTPS dans un navigateur (voir Dans un navigateur). Scanner un QR code utilise la caméra.